Article Sidebar

Download
PDF
Statistic
Read Counter : 976 Download : 523

Downloads

Download data is not yet available.

Main Article Content

Abstract

In this paper, Metallic Catalytic Converter (MCC) is installed in motorcycle exhausts to produce the minimum CO as well as to produce the optimum engine power. The results from previous research were collected and then used to predict the best MCC design using the Artificial Neural Network Multi-Objective Genetic Algorithm (ANN-MOGA). In addition, the ANN parameter tuning process was also carried out using the Taguchi method to find the initial weighting and bias that is able to provide the best and the most stable performance to predict the best MCC design. The best two sets of design solutions out of 70 sets of Pareto solutions were obtained by ANN-MOGA. Those two MCC designs are the optimum emission design and the optimum multi-objective design. The verification results show that the optimum multi-objective design tends to be superior in terms of CO emissions and engine power. In terms of CO emissions, the optimum multi-objective design gets a larger S/N ratio of -10.98, while the optimum emission design only gets an S/N ratio of -11.21. Meanwhile, in terms of engine power, the optimum multi-objective design gets a larger S/N ratio of 16.13, while the optimum emission design only gets an S/N ratio of 15.86 S/N. It is in line with the ANOVA test results which show that the optimum multi-objective design is proven to be better than the optimum emission design.

Keywords

Metallic Catalytic Converter Pareto solutions Artificial Neural Network Genetic Algorithm CO Emission Engine Performance

Article Details

Creative Commons License

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.

References

  1. J.-H. Tsai, Y.-C. Yao, P.-H. Huang, and H.-L. Chiang, “Fuel economy and volatile organic compound exhaust emission for motorcycles with various running mileages,” Aerosol and Air Quality Research, vol. 18, no. 12, pp. 3056–3067, 2018, doi: 10.4209/aaqr.2018.07.0264.
  2. O. A. Odunlami, O. K. Oderinde, F. A. Akeredolu, J. A. Sonibare, O. R. Obanla, and M. E. Ojewumi, “The effect of air-fuel ratio on tailpipe exhaust emission of motorcycles,” Fuel Communications, vol. 11, p. 100040, 2022, doi: 10.1016/j.jfueco.2021.100040.
  3. Y.-L. T. Nguyen, A.-T. Le, K. N. Duc, V. N. Duy, and C. D. Nguyen, “A study on emission and fuel consumption of motorcycles in idle mode and the impacts on air quality in Hanoi, Vietnam,” International Journal of Urban Sciences, vol. 25, no. 4, pp. 522–541, 2021, doi: 10.1080/12265934.2020.1871059.
  4. R. Anggrainy, W. Ruslan, D. L. Zariatin, R. A. Gilart, and T. Syam, “Effect of gasoline vaporizer tube (GVT) with magnetic field on spark-ignition engine: Investigation, discussion, and opinion,” Mechanical Engineering for Society and Industry, vol. 2, no. 2, pp. 98–106, 2022, doi: 10.31603/mesi.7075.
  5. L. M. Olalekan, O. Olatunde, F. I. Olufemi, and A. A. Olamide, “Mathematical modeling and cost comparison for electricity generation from petrol and liquified petroleum gas (LPG),” Mechanical Engineering for Society and Industry, vol. 2, no. 2, pp. 56–62, 2022, doi: 10.31603/mesi.6697.
  6. B. Waluyo and B. C. Purnomo, “Exhaust Gas Emissions of Homogeneous Gasoline-Methanol-(Ethanol) Blends,” Automotive Experiences, vol. 5, no. 2, pp. 173–181, 2022, doi: 10.31603/ae.6599.
  7. T. Dinh, K. Nguyen, T. Pham, and V. Nguyen, “Study on performance enhancement and emission reduction of used carburetor motorcycles fueled by flex-fuel gasoline-ethanol blends,” Journal of the Chinese Institute of Engineers, vol. 43, no. 5, pp. 477–488, 2020, doi: 10.1080/02533839.2020.1751719.
  8. T. Dinh Xuan, D. Vu Minh, B. P. Hoa, K. N. Duc, and V. Nguyen Duy, “Influence of ethanol-gasoline blended fuel on performance and emission characteristics of the test motorcycle engine,” Journal of the Air & Waste Management Association, vol. 72, no. 8, pp. 895–904, 2022, doi: 10.1080/10962247.2022.2064003.
  9. V. N. Duy, K. N. Duc, and N. C. Van, “Real-time driving cycle measurements of fuel consumption and pollutant emissions of a bi-fuel LPG-gasoline motorcycle,” Energy Conversion and Management: X, vol. 12, p. 100135, 2021, doi: 10.1016/j.ecmx.2021.100135.
  10. V. N. Duy, K. N. Duc, D. N. Cong, H. N. Xa, and T. Le Anh, “Experimental study on improving performance and emission characteristics of used motorcycle fueled with ethanol by exhaust gas heating transfer system,” Energy for Sustainable Development, vol. 51, pp. 56–62, 2019, doi: 10.1016/j.esd.2019.05.006.
  11. M. Real, R. Hedinger, B. Pla, and C. Onder, “Modelling three-way catalytic converter oriented to engine cold-start conditions,” International Journal of Engine Research, p. 146808741985314, May 2019, doi: 10.1177/1468087419853145.
  12. S. K. Haldar, Platinum-Nickel-Chromium Deposits. Elsevier, 2016.
  13. M. Pacella et al., “PGM-free CuO/LaCoO3 nanocomposites: New opportunities for TWC application,” Applied Catalysis B: Environmental, vol. 227, pp. 446–458, Jul. 2018, doi: 10.1016/j.apcatb.2018.01.053.
  14. I. Yakoumis, Ε. Polyzou, and A. M. Moschovi, “PROMETHEUS: A Copper-Based Polymetallic Catalyst for Automotive Applications. Part II: Catalytic Efficiency an Endurance as Compared with Original Catalysts,” Materials, vol. 14, no. 9, p. 2226, Apr. 2021, doi: 10.3390/ma14092226.
  15. Warju, Teknologi Reduksi Emisi Gas Buang Kendaraan Bermotor. Surabaya: Unesa University Press, 2013.
  16. P. Lang, N. Yuan, Q. Jiang, Y. Zhang, and J. Tang, “Recent Advances and Prospects of Metal‐Based Catalysts for Oxygen Reduction Reaction,” Energy Technology, vol. 8, no. 3, p. 1900984, Mar. 2020, doi: 10.1002/ente.201900984.
  17. E. Kritsanaviparkporn, F. M. Baena-Moreno, and T. R. Reina, “Catalytic Converters for Vehicle Exhaust: Fundamental Aspects and Technology Overview for Newcomers to the Field,” Chemistry, vol. 3, no. 2, pp. 630–646, May 2021, doi: 10.3390/chemistry3020044.
  18. M. Prabhahar et al., “Copper Oxide Nanoparticles Incorporated in the Metal Mesh Used to Enhance the Heat Transfer Performance of the Catalytic Converter and to Reduce Emission,” Journal of Nanomaterials, vol. 2022, pp. 1–9, Jul. 2022, doi: 10.1155/2022/9169713.
  19. A. G. Bell, Modern Engine Tuning. Haynes Publishing, 1997.
  20. S. Bhure, “Effect of Exhaust Back Pressure on Performance and Emission Characteristics of Diesel Engine Equipped with Diesel Oxidation Catalyst and Exhaust Gas Recirculation,” International Journal of Vehicle Structures and Systems, vol. 10, no. 3, Aug. 2018, doi: 10.4273/ijvss.10.3.09.
  21. W. Warju, N. S. Drastiawati, S. R. Ariyanto, and M. Nurtanto, “The effect of Titanium Dioxide (TiO2) based metallic catalytic converter on the four-stroke motorcycle engine performance,” Journal of Physics: Conference Series, vol. 1747, no. 1, p. 012031, Feb. 2021, doi: 10.1088/1742-6596/1747/1/012031.
  22. E. Ellyanie and D. Oktabri H, “The Effect of Brass (Cu-Zn) Catalytic Converter Muffler On Engine Performance,” Indonesian Journal of Engineering and Science, vol. 2, no. 2, pp. 035–043, Jul. 2021, doi: 10.51630/ijes.v2i2.20.
  23. S. S. Miriyala, V. R. Subramanian, and K. Mitra, “TRANSFORM-ANN for online optimization of complex industrial processes: Casting process as case study,” European Journal of Operational Research, vol. 264, no. 1, pp. 294–309, Jan. 2018, doi: 10.1016/j.ejor.2017.05.026.
  24. A. Hijazi, S. Al-Dahidi, and S. Altarazi, “A Novel Assisted Artificial Neural Network Modeling Approach for Improved Accuracy Using Small Datasets: Application in Residual Strength Evaluation of Panels with Multiple Site Damage Cracks,” Applied Sciences, vol. 10, no. 22, p. 8255, Nov. 2020, doi: 10.3390/app10228255.
  25. P. Ngatchou, A. Zarei, and A. El-Sharkawi, “Pareto Multi Objective Optimization,” in Proceedings of the 13th International Conference on, Intelligent Systems Application to Power Systems, pp. 84–91, doi: 10.1109/ISAP.2005.1599245.
  26. M. Akbari, P. Asadi, M. K. Besharati Givi, and G. Khodabandehlouie, “Artificial neural network and optimization,” in Advances in Friction-Stir Welding and Processing, Elsevier, 2014, pp. 543–599.
  27. K. Agbele, A. Adesina, D. Ekong, and O. Ayangbekun, “State-of-the-Art Review on Relevance of Genetic Algorithm to Internet Web Search,” Applied Computational Intelligence and Soft Computing, vol. 2012, pp. 1–7, 2012, doi: 10.1155/2012/152385.
  28. Warju and I. M. Muliatna, “Environmental Friendly Innovative Muffler Design Using Metallic Catalytic Converter Technology to Support the Blue Sky Program (1st Year of Funding),” Surabaya, 2012.
  29. Warju and I. M. Muliatna, “Environmentally Friendly Innovative Muffler Design Using Metallic Catalytic Converter Technology to Support the Blue Sky Program (2nd Year of Funding),” Surabaya, 2013.
  30. S. D. Sulistiono and Warju, “Performance of Metallic Catalytic Converter Made from Nickel-Plated Brass Against Engine Performance, Reduction of Exhaust Emissions, and Noise Levels of Yamaha V-Ixion Motorcycles in 2011,” Universitas Negeri Surabaya, 2014.
  31. E. W. Amboro and Warju, “The Effect of Using Metallic Catalytic Converter Made from Brass and Application of SASS Technology on Emissions of the Honda New Mega Pro Motorcycle,” Jurnal Teknik Mesin (JTM), vol. 1, no. 2, 2013.
  32. Warju, “Eco-Friendly Motorcycle Exhaust Products with Metallic Catalytic Converter Technology,” Surabaya, 2017.
  33. Warju, A. N. F. Ganda, Suprayitno, and J.-C. Yu, “Robust Parameter Design Muffler Berteknologi Metallic Catalytic Converter dan Implementasinya untuk Mereduksi Emisi Gas Buang Dan Meningkatkan Performa Mesin Menggunakan Dual Response Surface Method,” Surabaya, 2021.
  34. S. R. Ariyanto, R. Wulandari, Suprayitno, and P. I. Purboputro, “Pengaruh Metallic Catalytic Converter Tembaga Berlapis Chrome Dalam Menurunkan Emisi Gas Buang Mesin Sepeda Motor Empat Langkah,” Jurnal Media Mesin, vol. 23, no. 1, pp. 44–51, 2022, doi: 10.23917/mesin.v23i1.16604.
  35. P. Bernard, P. Stelmachowski, P. Broś, W. Makowski, and A. Kotarba, “Demonstration of the Influence of Specific Surface Area on Reaction Rate in Heterogeneous Catalysis,” Journal of Chemical Education, vol. 98, no. 3, pp. 935–940, Mar. 2021, doi: 10.1021/acs.jchemed.0c01101.
  36. H. Elçiçek, E. Akdoğan, and S. Karagöz, “The Use of Artificial Neural Network for Prediction of Dissolution Kinetics,” The Scientific World Journal, vol. 2014, pp. 1–9, 2014, doi: 10.1155/2014/194874.
  37. S. Abirami and P. Chitra, “Energy-efficient edge based real-time healthcare support system,” in Advances in Computers, 2020, pp. 339–368.
  38. P. Sahoo, “Tribological performance of electroless Ni-P coatings,” in Materials and Surface Engineering, Elsevier, 2012, pp. 163–205.
  39. A. C. Mitra, M. Jawarkar, T. Soni, and G. R. Kiranchand, “Implementation of Taguchi Method for Robust Suspension Design,” Procedia Engineering, vol. 144, pp. 77–84, 2016, doi: 10.1016/j.proeng.2016.05.009.
  40. K. G. Sheela and S. N. Deepa, “Review on Methods to Fix Number of Hidden Neurons in Neural Networks,” Mathematical Problems in Engineering, vol. 2013, pp. 1–11, 2013, doi: 10.1155/2013/425740.
  41. K.-W. Lin and Y.-C. Chang, “Use of the Taguchi Method to Optimize an Immunodetection System for Quantitative Analysis of a Rapid Test,” Diagnostics, vol. 11, no. 7, p. 1179, Jun. 2021, doi: 10.3390/diagnostics11071179.
  42. R. V. Aleksandrovich and G. Siamak, “The Effect of Tool Construction and Cutting Parameters on Surface Roughness and Vibration in Turning of AISI 1045 Steel Using Taguchi Method,” Modern Mechanical Engineering, vol. 04, no. 01, pp. 8–18, 2014, doi: 10.4236/mme.2014.41002.
  43. W. S. Alaloul and A. H. Qureshi, “Data Processing Using Artificial Neural Networks,” in Dynamic Data Assimilation - Beating the Uncertainties, IntechOpen, 2020.
  44. M. H. Esfe, S. A. Eftekhari, M. Hekmatifar, and D. Toghraie, “A well-trained artificial neural network for predicting the rheological behavior of MWCNT–Al2O3 (30–70%)/oil SAE40 hybrid nanofluid,” Scientific Reports, vol. 11, no. 1, p. 17696, Aug. 2021, doi: 10.1038/s41598-021-96808-4.
  45. A. Shafiq, A. Batur Çolak, T. Naz Sindhu, S. Ahmad Lone, A. Alsubie, and F. Jarad, “Comparative study of artificial neural network versus parametric method in COVID-19 data analysis,” Results in Physics, vol. 38, p. 105613, Jul. 2022, doi: 10.1016/j.rinp.2022.105613.
  46. M. S. Umam, M. Mustafid, and S. Suryono, “A hybrid genetic algorithm and tabu search for minimizing makespan in flow shop scheduling problem,” Journal of King Saud University - Computer and Information Sciences, Sep. 2021, doi: 10.1016/j.jksuci.2021.08.025.
  47. H. M. Pandey, “Performance Evaluation of Selection Methods of Genetic Algorithm and Network Security Concerns,” Procedia Computer Science, vol. 78, pp. 13–18, 2016, doi: 10.1016/j.procs.2016.02.004.
  48. Y.-B. Li, H.-B. Sang, X. Xiong, and Y.-R. Li, “An Improved Adaptive Genetic Algorithm for Two-Dimensional Rectangular Packing Problem,” Applied Sciences, vol. 11, no. 1, p. 413, Jan. 2021, doi: 10.3390/app11010413.
  49. X.-S. Yang, “Genetic Algorithms,” in Nature-Inspired Optimization Algorithms, Elsevier, 2014, pp. 77–87.
  50. A. Sánchez-Chica, E. Zulueta, D. Teso-Fz-Betoño, P. Martínez-Filgueira, and U. Fernandez-Gamiz, “ANN-Based Stop Criteria for a Genetic Algorithm Applied to Air Impingement Design,” Energies, vol. 13, no. 1, p. 16, Dec. 2019, doi: 10.3390/en13010016.
  51. R. S. Nursal, A. H. Hashim, N. I. Nordin, M. A. Abdul Hamid, and M. R. Danuri, “CFD analysis on the effects of exhaust backpressure generated by four-stroke marine diesel generator after modification of silencer and exhaust flow design,” ARPN Journal of Engineering and Applied Sciences, vol. 12, no. 4, pp. 1271–1280, 2017.
  52. R. Fox, A. McDonald, and P. J. Pritchard, Introduction to Fluid Mechanics, 8th ed. John Wiley & Sons, Inc, 2011.
  53. SNI 09-7118.2-2005, Exhaust gas emissions - Moving sources - Part 2: How to test motorized M, N, and O category vehicles with compression-ignition engine under free acceleration conditions. Indonesia: National Standardization Agency (NSA).
  54. SAE J1349, Engine Power Test Code-Spark Ignition and Compression Ignition-Net Power Rating. Warrendale: SAE International, 2004.
  55. N. Gunantara, “A review of multi-objective optimization: Methods and its applications,” Cogent Engineering, vol. 5, no. 1, p. 1502242, Jan. 2018, doi: 10.1080/23311916.2018.1502242.
  56. S. Khanmohammadi, O. Kizilkan, and F. Musharavati, “Multiobjective optimization of a geothermal power plant,” in Thermodynamic Analysis and Optimization of Geothermal Power Plants, Elsevier, 2021, pp. 279–291.
  57. R. Kumar, R. Singh, I. S. Ahuja, and K. N. Karn, “Joining of 3D Printed Dissimilar Thermoplastics With Friction Welding: A Case Study,” in Encyclopedia of Renewable and Sustainable Materials, Elsevier, 2020, pp. 97–108.
  58. N. Azri, R. Irmawati, U. I. Nda-Umar, M. I. Saiman, and Y. H. Taufiq-Yap, “Promotional effect of transition metals (Cu, Ni, Co, Fe, Zn)–supported on dolomite for hydrogenolysis of glycerol into 1,2-propanediol,” Arabian Journal of Chemistry, vol. 14, no. 4, p. 103047, Apr. 2021, doi: 10.1016/j.arabjc.2021.103047.
  59. H. Li et al., “Catalytic hydrogenation of maleic anhydride to γ-butyrolactone over a high-performance hierarchical Ni-Zr-MFI catalyst,” Journal of Catalysis, vol. 410, pp. 69–83, Jun. 2022, doi: 10.1016/j.jcat.2022.04.011.
  60. V. V. Ranade and S. S. Joshi, “Catalysis and Catalytic Processes,” in Industrial Catalytic Processes for Fine and Specialty Chemicals, Elsevier, 2016, pp. 1–14.
  61. L. Piccolo, “Surface Studies of Catalysis by Metals: Nanosize and Alloying Effects,” 2012, pp. 369–404.
  62. M. H. S. Morad, “Development of new highly active nano gold catalysts for selective oxidation reactions,” University of Cardiff, 2014.
  63. I. Chorkendorff and J. W. Niemantsverdriet, Concepts of Modern Catalysis and Kinetics. Strauss Offsetdruck: Wiley-VCH, 2003.
  64. S. Dey and N. S. Mehta, “Selection of Manganese oxide catalysts for catalytic oxidation of Carbon monoxide at ambient conditions,” Resources, Environment and Sustainability, vol. 1, p. 100003, Sep. 2020, doi: 10.1016/j.resenv.2020.100003.
  65. R. Flitney, “Materials,” in Seals and Sealing Handbook, Elsevier, 2014, pp. 369–435.
  66. M. Bhandwal, M. Kumar, M. Sharma, U. Srivastava, A. Verma, and R. K. Tyagi, “The effect of using the turbulence enhancement unit before the catalytic converter in diesel engine emissions,” International Journal of Ambient Energy, vol. 39, no. 1, pp. 73–77, Jan. 2018, doi: 10.1080/01430750.2016.1237889.